SHARP DW-E16FA Air Purifying Dehumidifier User Manual – Manuals+

09/07/2022 admin
The water leaks
  • Make sure you do not tilt, knock over or drop the main unit.
  • Check to see if the hose is disconnected from the drain outlet of the main unit during continuous drainage.
    • Install the hose by pushing it all the way in.
—E – 21——— The humidity level does not go down
  • The room may be too big.
  • The opening/closing of windows and doors may be too frequent.
  • Check to see if a humidifier or other devices that release steam is in use.
E – 14 Laundry does not dry
  • Check to see if laundry drying (Auto) mode is operating.
    • The AUTO operation will stop automatically after a maximum of 3 hours.
      Laundry may not be dried enough depending on the room situation. Operate AUTO mode again or switch to the CONTINUOUS laundry drying operation. (HIGH/MED/LOW)
E – 3E – 3 Sound There is a sound at the start of operation/during operation/when the unit stops
  • Buzzing sound…This is the operating sound of the compressor.
  • Whipping, howling sound…This is the sound of refrigerant (coolant) circulation
E – 3E – 13E – 24 The sound is too loud
  • The unit will sound loudly for the first few seconds upon power-on when the room temperature is low. (This duration will vary with the temperature.)
  • Check to see if the dehumidifier is properly placed on the floor or if the floor is unstable.
    • Use the unit at a level, stable place with free of vibration.
  • Check to see if the rear panel is clogged.
    • Clean the rear panel.
— Buzzing sounds are heard from the air outlet
  • This is the sound of generating Plasmacluster ions, not a malfunction. Sound volume varies with the working environment and operation mode, but the efficiency is not affected.
Smell Odors or smokes are hard to remove
  • Check to see if the filters are enclosed in a plastic bag.
    • Take out the filters from the plastic bag.
  • Check to see if the wind from the air outlet is weak.
    • Clean the dust and dirt off the following parts:
      • Rear panel
      • Sensor
      • Filters
E – 12E – 22 ~ 2 Odor comes out from the air outle
  • Check to see if the unit is used in a room with a strong odor. If the unit is used where there is a strong odor caused by smoking or barbecue, the filter may give off odors in several weeks or months and thus needs to be replaced.
    • It is recommended to use the product together with ventilation of the room.
  • When the unit has been used for a long time, odor and dirt may adhere to the inside.
    • Please regularly clean the unit and dry its inside.
  • Check to see if the dirt on the filters becomes heavy.
    • Clean the filters, or replace them if you are bothered.
  • When Plasmacluster ions are generated, a trace of ozone will be generated, which gives off an odor from the air outlet. However, its quantity is tiny and the health will not be harmed.

E – 22~25E – 22 ~ 25E – 23— Display ODOR Indicator Light does not change its color
  • After the operation starts, ODOR Indicator Light does not change its color for the time being due to unsteady sensitivity of the sensor. After a few minutes, sensitivity of the sensor becomes steady.
  • If ODOR Indicator Light remains green, the air is fresh. It is hard for the sensor to detect in some places. It is normal if ODOR Indicator Light changes its color when cigarette smoke is blown to the sensor.
  • If the operation is started in a room with a strong odor, sensitivity of the odor sensor may become blunt.
    • Please continue the air purifying operation (MED) for several hours or 1 day.
  • Dust may accumulate on the sensor.
    • Please remove the rear panel and the filters and clean them with a cleaner through the hole as shown in the right figure.
——E – 17E – 25 ODOR Indicator Light does not turn green
  • It may not turn green due to dirt comes from outdoors when the window or the door is opened frequently or the room is of poor airtightness.
ODOR Indicator Light often switches
  • It may respond to wind and temperature change caused by opening and closing of the door frequently.
— The AIR PURIFYING indicator light does not turn off — Float The float comes off
  • Install the float by following the procedure below.
— The unit does not operate The unit cannot operate Buttons do not work
  • Check the CHILD LOCK setting.
    • If locked, release the child lock.
The operation stops
  • Check the power plug.
    • If not inserted, insert the power plug into an outlet.
  • Check to see if there is a power outage.
    • If there is a power outage, wait until the power is resumed.
——
  • Check to see if the water tank is properly placed.
    • If not, place the water tank correctly.
  • Check to see if the water tank is full.
    • If the tank is full, drain the water.
  • Check to see if the float is properly placed.
    • If not, place the float properly
E – 20E – 20E – 30
  • The operation has stopped with the Auto Off function.
    • Press the OFF button to stop the indicator light from blinking, and start the operation again. When using continuously, disable the Auto Off function.
E – 11
  • The water tank becomes full and the operation has stopped with the Auto Off function.
    • Empty the water tank, press the OFF button to stop the indicator light from blinking, and start the operation again.
E – 11,20
  • Laundry drying (Auto) operation has completed, and the operation has stopped.
    • Press the OFF button to stop the indicator light from blinking, and start the operation again.
E – 14 Other indicator lights blinking
  • The unit may malfunction.
    •  Please consult the store where you purchased the product or SHARP authorized service center.
— The unit falls down The main unit falls down (during dehumidifying or laundry drying operation or while water enters the tank)
  • When the main unit falls down while water enters the tank, pull out the power plug and consult the store where you purchased the product or SHARP authorized service center.
—

Sửa Tủ Lạnh

Trung Tâm Bảo Hành

Alternate Text Gọi ngay